單列角接觸球淮安INA軸承能承受單向軸向載荷。單列角接觸球軸承通常與其余軸承成對使用。這種軸承是不可分割的設計，內外環兩側的軸肩尺寸是不同的。肩部越小，滾珠軸承越多，承載能力越高。

Single row angular contact ball Huaian INA bearing can bear unidirectional axial load. Single row angular contact ball bearings are usually used in pairs with other bearings. The bearing is an inseparable design, and the shoulder sizes on both sides of the inner and outer rings are different. The smaller the shoulder, the more ball bearings, the higher the load-carrying capacity.

該軸承具有接觸角，適用于承受軸向載荷或單向復合載荷。

The bearing has contact angle and is suitable for bearing axial load or unidirectional composite load.

在結構中，軸承在承受徑向載荷后會軸向分離，所以兩個軸承將成對使用，或者兩個以上的軸承將成對使用。單列角接觸球軸承采用預緊法可提高剛度，適用于高精度機床主軸。

In the structure, bearings will be axially separated after bearing radial load, so two bearings will be used in pairs, or more than two bearings will be used in pairs. Single row angular contact ball bearings can improve stiffness by pre-tightening method, which is suitable for spindle of high precision machine tools.

通常，接觸角為30度（代碼A UU）和40度（代碼B）角接觸球軸承保持架。然而，合成樹脂保持架或聚酰胺保持架也在不同的條件下使用。尺寸表中記錄的基本額定載荷基于保持架面積。

Usually, contact angles are 30 degrees (code A UU) and 40 degrees (code B) angular contact ball bearing cages. However, synthetic resin cages or polyamide cages are also used under different conditions. The basic rated load recorded in the dimension table is based on cage area.

萬向成對軸承主要成對使用。一般配套淮安INA軸承均經過特殊加工。當軸承彼此靠近安裝時，任何組合都可以在不使用墊圈或類似裝置的情況下實現給定的內部間隙或預加載，以及平均負載分布。

Universal paired bearings are mainly used in pairs. Generally matching Huaian INA bearings are specially processed. When bearings are installed close to each other, any combination can achieve a given internal clearance or preload, as well as an average load distribution without using gaskets or similar devices.

當單個軸承的承載能力不足時（槽結構），或當使用兩個方向的組合荷載或軸向荷載（背對背或面對面配置）時，使用匹配軸承。

Matched bearings are used when the bearing capacity of a single bearing is insufficient (groove structure), or when combined loads in two directions or axial loads (back-to-back or face-to-face configuration) are used.

背靠背配置：后碼為db（如7000/db），背靠背軸承的載重線與軸承軸分離。兩個方向的軸向載荷都可以承受，但每個方向的載荷只能由一個淮安INA軸承承受。背對背安裝軸承提供相對剛性的軸承配置，可以承受傾覆力矩。

Back-to-back configuration: the rear code is DB (e.g. 7000/db), the load line of back-to-back bearing is separated from the bearing shaft. Axial loads in both directions can be sustained, but loads in each direction can only be sustained by a Huaian INA bearing. Back-to-back mounted bearings provide relatively rigid bearing configurations that can withstand overturning moments.

面對面配置：后代數為df（如7000/df），面對面匹配軸承的載荷集中在軸承軸上。兩個方向的軸向載荷都可以承受，但每個方向的載荷只能由一個軸承承受。這種配置不像背對背配對那樣剛性，不適合傾覆力矩。該結構的剛度和傾覆力矩不如DB結構。軸承能承受雙軸載荷。

Face-to-face configuration: the number of offspring is DF (e.g. 7000/df), and the load of face-to-face matched bearings is concentrated on the bearing shaft. Axial loads in both directions can be sustained, but loads in each direction can only be sustained by one bearing. This configuration is not as rigid as back-to-back pairing and is not suitable for overturning moment. The stiffness and overturning moment of this structure are not as good as those of DB structure. Bearings can withstand biaxial loads.

系列配置：后碼為dt（如7000/dt）。在串聯結構中，載荷線平行，徑向和軸向載荷由軸承均勻分擔。然而，淮安INA軸承組只能承受作用于一個方向的軸向載荷。如果軸向載荷的作用方向相反或存在復合載荷，則bi須添加第三個具有相對串聯對調整的軸承。該結構還可用于同一支架上串接三個或三個以上軸承，但只能承受單向軸向載荷。通常情況下，為了平衡和限.制軸的軸向位移，應安裝另一個軸承來承受另一個方向的軸向載荷。

Series Configuration: The rear code is DT (e.g. 7000/dt). In the series structure, the load lines are parallel, and the radial and axial loads are evenly shared by the bearings. However, Huaian INA bearing group can only bear the axial load acting in one direction. If the direction of action of the axial load is opposite or there is a composite load, the Bi must add a third bearing with relative series pair adjustment. The structure can also be used to connect three or more bearings in series on the same support, but can only bear unidirectional axial load. Usually, in order to balance and limit the axial displacement of the shafting, another bearing should be installed to bear the axial load in the other direction.

 

文章來自：淮安SKF軸承 www.wh-skf.com

Article from: Huaian SKF Bearing www.wh-skf.com

文章來自：淮安INA軸承 www.ina-china.cn

Article from: Huaian INA Bearing www.ina-China.cn

文章來自：淮安NSK軸承 www.klbbearings.com

Article from: Huaian NSK Bearing www.klbbearings.com

 

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757

 

【商家簡介】鴻御（上海）國際貿易有限公司是一家以進口軸承銷售為主的機電公司，公司位于上海，本公司在工業領域已有多年的軸承配套及工業服務經驗，在新老客戶有著良好的口碑。公司專業代理進口軸承，涉及品牌：德國FAG軸承、INA軸承，日本NSK軸承、IKO軸承、KOYO軸承、NACHI軸承，瑞典進口軸承，美國TIMKEN軸承等，涉及種類：向心球軸承、向心球面軸承、深溝球軸承、向心球面滾子軸承、圓柱滾子軸承、滾針軸承、向心推力球軸承等。銷售行業主要包括:工礦企業、鋼廠、機械設備、鐵路、工程機械發電廠、石化機械、鉆機等 公司以先... 【溫馨提示】以上是鴻御（上海）國際貿易有限公司供應的滾針軸承--INA軸承MF-2020-如何對淮安INA軸承進行接觸與通用配對MF-2020的詳細信息，歡迎您在驛路商務查看滾針軸承的新的價格、廠家、型號、圖片等信息。本頁所展示的信息由企業自行提供，內容的真實性、準確性和合法性由發布企業負責，"驛路商務"對此不承擔任何保證責任。同時鄭重提醒各位買/賣家，交易前請?jiān)敿?xì)核實對方身份，切勿隨意打款或發貨，謹防上當受騙。如發現虛假信息，請積極舉報。[我要舉報]

• 下一產品：up復合耐磨板up-x750(10+6)生產廠家
• 上一產品：鎮江冷柜多少錢-鎮江冷柜批發銷售