在主機上安裝淮安NSK軸承后，如果測量軸承主軸的徑向跳動，可以發現每一個轉動的測量值都有一定的變化；連續測量時，可以發現，經過一定的轉動后，變化將近似重復。測量變化程度的指標是圓旋轉的精度。重復旋轉近似于循環旋轉精度的準周期性。準周期變化范圍大，即周期旋轉精度差。

After installing the Huaian NSK bearing on the main engine, if the radial runout of the bearing spindle is measured, it can be found that the measured value of each rotation has a certain change; when continuously measuring, it can be found that after a certain rotation, the change will be approximately repeated. The index of measuring the degree of change is the accuracy of circular rotation. Repeated rotation approximates the quasi-periodicity of cyclic rotation accuracy. The range of quasi-periodic variation is large, that is, the precision of periodic rotation is poor.

如果對軸承主軸施加適當?shù)念A(yù)緊力，轉速將逐漸提高，接近工作轉速，從而實現軸承的“磨合”功能，提高主軸旋轉精度。

If proper preloading force is applied to the bearing spindle, the speed will gradually increase, close to the working speed, thus realizing the "running-in" function of the bearing and improving the spindle rotation accuracy.

軸承安裝后，為了檢查安裝是否正確，應進行操作檢查。小型機器可以用手旋轉以確保平穩旋轉。淮安NSK軸承檢查項目包括：異物、傷痕、操作bu良造成的壓痕、安裝.bu良、力矩不穩定造成的安裝座加工bu良、間隙過小、安裝誤差、力矩過大造成的密封摩擦等，如無異常，可啟動供電運行。

After the bearing is installed, in order to check whether the installation is correct, the operation inspection should be carried out. Small machines can be rotated by hand to ensure smooth rotation. Huaian NSK bearing inspection items include: foreign body, scar, indentation caused by operation Bu Liang, installation Bu Liang, installation seat processing Bu Liang caused by unstable moment, too small clearance, installation error, sealing friction caused by excessive moment, etc. If there is no abnormality, power supply operation can be started.

大型機械不能手動旋轉?？蛰d啟動后立即切斷電源。機器閑置。檢查轉動部件的振動、噪聲和接觸情況，確認無異常，進入動力運行。

Large machinery cannot rotate manually. Cut off the power supply immediately after no-load start-up. The machine is idle. Check the vibration, noise and contact of the rotating parts, confirm that there is no abnormality, and enter the power operation.

當電源運行時，空載、低速啟動，并緩慢增加到規定的額定工作條件。在調試過程中，檢查項目包括異常噪音、淮安NSK軸承溫度變化、潤滑油泄漏或變色。如果發現任何異常，應立即停止機器，必要時應拆下軸承進行檢查。

When the power supply is running, no-load, low-speed start, and slowly increase to the specified rated working conditions. During commissioning, the inspection items include abnormal noise, temperature change of Huaian NSK bearing, oil leakage or discoloration. If any abnormalities are found, the machine should be stopped immediately and the bearings should be removed for inspection if necessary.

軸承溫度通?？梢詮妮S承座的外部溫度推斷出來。但采用油孔直接測量軸承外圈溫度更為準確。軸承溫度從運行開始逐漸升高，通常在溫度穩定后1至2小時。如果軸承安裝不當，溫度會急劇上升，出現異常高溫。其原因包括潤滑油過多、軸承間隙過小、安裝.bu良、密封裝置摩擦過大、軸承結構選擇不當、潤滑方式不合理等，也是高速旋轉的原因。

Bearing temperature can usually be deduced from the external temperature of the bearing seat. But it is more accurate to use oil hole to measure the temperature of bearing outer ring directly. Bearing temperature gradually increases from the beginning of operation, usually 1 to 2 hours after temperature stabilization. If the bearing is not properly installed, the temperature will rise sharply and abnormal high temperature will occur. The reasons include too much lubricating oil, too small bearing clearance, good installation. bu, too much friction of sealing device, improper selection of bearing structure, unreasonable lubrication mode and so on, which are also the reasons for high-speed rotation.

聽診器檢測淮安NSK軸承的旋轉聲音。結果表明，金屬噪聲較大，聲音異常。其原因包括潤滑bu良、軸或軸承座精度差、軸承損壞、異物侵入等。

Stethoscope detects the rotating sound of Huaian NSK bearing. The results show that the metal noise is large and the sound is abnormal. The reasons include good lubrication bu, poor precision of shaft or bearing seat, bearing damage, foreign body intrusion, etc.

 

文章來自：淮安SKF軸承 www.wh-skf.com

Article from: Huaian SKF Bearing www.wh-skf.com

文章來自：淮安INA軸承 www.ina-china.cn

Article from: Huaian INA Bearing www.ina-China.cn

文章來自：淮安NSK軸承 www.klbbearings.com

Article from: Huaian NSK Bearing www.klbbearings.com

 

QQ：524085168

電話：0510-81207777

手機：13311666672/13395185757

 

【商家簡介】鴻御（上海）國際貿易有限公司是一家以進口軸承銷售為主的機電公司，公司位于上海，本公司在工業領域已有多年的軸承配套及工業服務經驗，在新老客戶有著良好的口碑。公司專業代理進口軸承，涉及品牌：德國FAG軸承、INA軸承，日本NSK軸承、IKO軸承、KOYO軸承、NACHI軸承，瑞典進口軸承，美國TIMKEN軸承等，涉及種類：向心球軸承、向心球面軸承、深溝球軸承、向心球面滾子軸承、圓柱滾子軸承、滾針軸承、向心推力球軸承等。銷售行業主要包括:工礦企業、鋼廠、機械設備、鐵路、工程機械發電廠、石化機械、鉆機等 公司以先... 【溫馨提示】以上是鴻御（上海）國際貿易有限公司供應的深溝球軸承--NSK軸承6011-ZN-淮安NSK軸承6011-ZN預緊力的主軸預加的詳細信息，歡迎您在驛路商務查看深溝球軸承的新的價格、廠家、型號、圖片等信息。本頁所展示的信息由企業自行提供，內容的真實性、準確性和合法性由發布企業負責，"驛路商務"對此不承擔任何保證責任。同時鄭重提醒各位買/賣家，交易前請詳細核實對方身份，切勿隨意打款或發貨，謹防上當受騙。如發現虛假信息，請積極舉報。[我要舉報]

• 下一產品：雙金屬復合耐磨板up-x650(10+10)多少錢一噸？
• 上一產品：up耐磨板up-x750(10+8)平方米價格